Download them from the links above.The original purpose of this interface was to support the expansion controllers of the Intellivision and Colecovision consoles. The help file explains how to set this up. Are the manuals and overlays available in the game Nostalgia supports the display of a game's box and overlay images within the emulator. Game ROM images: These can be download from the internet or purchased from Intellivision Productions.
![]() ![]() Intellivision Emulator How To Set ThisDongle for connecting the original Intellivision controllers without modifying the cord is available separately (see photo below) BlueMSX supports the Colecovision controllers. CoolCV, AdamEM, and MESS supports the Colecovision spinner (Super Action spinner, steering wheel, and rollerball) through mouse and joystick support. It works natively in the operating system. Supports the Intellivision ECS keyboard. Supports all 8 directions of the Colecovision, Atari, Genesis 3/6 controllers, and all other 8 direction controllers. ( see support section below) Supports the Colecovision spinner which is used by the Super Action Controller, the Steering Wheel, and the RollerBall through the emulator's mouse and joystick support. Currently only supported by the jzIntv emulator Supports the Intellivision Music Synthesizer. Music Synthesizer - left switch DOWN, right switch DOWNNOTE: The interface (VERSION 2 only) MUST be unplgged from the USB and reconnected when switching modes.- for ALL controllers excluding the controllers listed below ECS Keyboard - left switch DOWN, right switch UP Intellivision Hand Controllers (non-Flashback) - left switch UP, right switch DOWN Auto Sense Mode - left switch UP, right switch UP- for ALL controllers excluding the ECS Keyboard and Music Synthesizer The side with the label is considered the TOP / UP side. See the interface label for reference. After making the changes, press the black button. Atari CX22/CX80 Trackball - left switch DOWN, right switch DOWNNOTE: The switches can be changed while the USB is plugged in (VERSION 3 only). Atari ST Mouse - left switch UP, right switch DOWN Atari 2600 Paddles - hold paddle #1 button Amiga/Commodore controller, press fire button or button #1 on 2 button controllers. keep holding the required controller key/button until the LED is flashing regularly (should not take more than a second or two) press and hold the required controller key/button Gamepad "A" (VERSION 2 - for Sega Genesis use START)The default mode (if no buttons are pressed when pluggin in the unit) remembers the last controller last recognized.To have the VERSION 2 interface recognize a controller below, press and hold for 5 seconds the required key/button while plugging in the USB or turning on your system if the USB is already connected.To have the VERSION 3 interface recognize a controller below Switches affect jack/controller B only.Autosense Mode supports all supported controllers.The GENERAL RULE for all controllers is to hold first option below that applies while triggering AutoSense: Gemini Dual Command - knob towards center All Famicon, NES, and SNES - hold A+B for button A/B X/Y swap Connect the steering after the controller is recognized. Coleco Steering Wheel: connect a Coleco controller and press zero. Coleco Rollerball: the switch should be set to Rollerball (not Joystick) Only one controller in port A is recognized. TI-99 controller, press button #1. MSX and X68000 controller, press fire button or button #1 on 2 button controllers. Intellivision ECS Piano - only on power up, hold the left or right most end key Trak-ball/mouse can only be used in jack B. Atari 2600 Driving may be miss-detected - use joystick or paddles for AutoSense, then change to driving Analog controls (2600 paddles, 2800/SVAII knob, Bally Astrocade knob) turned full right can cause the controller to be miss-detected. Summer in the country 1980 full movie downloadThe Atari 2600 paddles are part of a "2600-daptor" mode.
0 Comments
Leave a Reply. |
AuthorCedric ArchivesCategories |